14kW Generac Generator Sizing and ATS Choices for San Antonio Homes
Will a 14kW Generac generator power your San Antonio home? See how load sizing, AC starting surge, the ATS and gas supply decide the answer.
Quick answer
A 14kW Generac generator can carry many essential circuits in a San Antonio home, and Generac rates its 14kW model 7258 for 14 kW on natural gas or propane. Whether it covers your home depends on sizing by load: central AC starting load, electric heat or water heating, well or pool pumps, and whether load-management modules will shed large loads. Pair it with an ATS matched to your service equipment, and confirm the gas supply can feed it under load.
Article Topics
- 14kW Generac Generator Specs That Matter for Sizing
- What a 14kW Standby Generator Can Usually Power
- How to Size a 14kW Generac Generator for Your Home
- Loads That Change the Answer
- What Comes in a 14kW Package
- Choosing the ATS for a 14kW Generac Generator: Service-Rated or Not
- Gas Supply at Full Load
- Placement, Noise and Permits in San Antonio
- Keeping a 14kW Generator Ready After Installation
- Comparing 14kW Package Prices
- Frequently asked questions
A 14kW Generac generator is one of the most common standby sizes San Antonio homeowners price out, and Generac rates its 14kW home standby model for 14,000 running watts on either natural gas or propane. Search for a 14kW Generac with an automatic transfer switch (ATS) and you will find package prices quickly. Whether that size fits your home is a different question, and it depends on your loads, your service equipment and your gas supply.
Start with what the spec sheet actually says, then compare it with the way your house uses power on a hot afternoon or a cold morning. If you plan to have the system installed, C.S.W. Power Solutions can walk through those numbers with you as part of a home generator installation estimate.
14kW Generac Generator Specs That Matter for Sizing
Generac's product page for its 14kW home standby generator (model 7258) lists the figures below. Check the page for the exact model on your quote, because packages, controllers and included parts change between model numbers.
| Spec | Listed value | Why it matters to you |
|---|---|---|
| Rated continuous power | 14 kW on natural gas and 14 kW on propane | Your running load plus the largest motor start has to fit inside this number. |
| Natural gas use | 189 cu ft/hr at 50% load, 243 cu ft/hr at 100% load | Your meter and piping have to deliver this volume while other gas appliances run. |
| Propane use | 1.76 gal/hr at 50% load, 2.92 gal/hr at 100% load | Tank size and refill access set how long you can run in a long outage. |
| Fuel pressure requirement | 3.5–7 in. water column on natural gas; 10–12 in. water column on propane, at the generator inlet across all load ranges | Low pressure under load can cause hard starts and shutdowns. |
| Transfer switch | Not included with model 7258; bundled with model 7323 | Compare packages model number by model number. |
| Warranty | 5-year limited warranty listed by Generac | Read Generac's terms for your exact model. |
What a 14kW Standby Generator Can Usually Power
A 14kW unit is best viewed as a strong essential-load system rather than a guaranteed whole-house solution. It can often support refrigerators, freezers, lighting, garage doors, internet equipment, outlets, some kitchen loads and selected comfort equipment when the loads are managed. The right answer comes from a load review, not square footage.
Generac describes three ways to plan coverage: essential-circuit coverage, where a packaged transfer switch carries a set number of circuits; managed whole-house coverage, where a smaller generator sheds non-essential loads when capacity runs low and restores them later; and complete whole-house coverage with a larger unit and the matching transfer switch. Where a 14kW unit lands among those three depends on your load review. Generac also says its own customer support cannot size a generator remotely, because sizing needs someone on site to inspect the loads and check local code.
How to Size a 14kW Generac Generator for Your Home
Generac's sizing guidance is to match the generator to your peak electrical load, not your square footage. Its rule of thumb adds the running watts of everything you want powered to the single largest starting surge. Motors are the reason: Generac notes that starting wattage is often two to three times the running figure.
- List the circuits that must stay on in an outage: refrigeration, lighting, internet, medical equipment, the garage door and the comfort loads you care about.
- Note the large motor loads, especially central air conditioning, heat pumps, well pumps and pool pumps.
- Add the running loads, then add the largest single starting surge.
- Compare the total with 14kW, leaving room for loads that cycle on together.
- If the total is close to or over 14kW, decide whether load management or a larger unit is the better fit.
Central air is the load that most often decides the answer. Generac's sizing guide notes that a 3-ton central AC unit may need up to 15kW to 18kW of starting power, and it suggests pairing a 14kW or 18kW generator with a load manager or soft start kit instead of oversizing. In a summer outage, the compressor start is often the hardest moment for an undersized setup, so have a licensed electrician measure the actual loads before you commit.
Loads That Change the Answer
- Central air-conditioning starting load.
- Electric heat or an electric water heater.
- Well pumps and pool equipment.
- Large electric cooking appliances.
- Medical or other critical equipment that must stay on.
Load-management modules can let a smaller generator cover more of the house by shedding large loads in turn. Whether that works for you is part of the load review.
Some transfer switches build this in. Generac's 100-amp service-entrance load center transfer switch, for example, can manage up to four HVAC loads without additional hardware, and Generac sells a separate Load Manager through its dealers for other large loads. Ask which load-management hardware is in the quote and exactly which loads it will control.
What Comes in a 14kW Package
Most packages include the outdoor generator and an automatic transfer switch. Before buying, confirm the exact model number, fuel type, transfer switch amperage and type, warranty, connectivity module, battery and pad requirements, and whether load-management accessories are included.
Read the model number closely. Generac lists its 14kW model 7258 as the generator alone, with transfer switches sold separately, while model 7323 is listed as a 14kW generator with transfer switch. The 7258 spec table also calls for a specific 12-volt AGM battery type, so confirm whether the battery is part of the price you are comparing.
Choosing the ATS for a 14kW Generac Generator: Service-Rated or Not
The transfer switch must match the electrical service and installation design. A service-rated ATS can serve as service equipment in certain configurations, while a non-service-rated ATS is installed downstream of the existing service disconnect. The difference affects panel layout, conductor routing, grounding and bonding, utility coordination and inspection. Because transfer equipment prevents dangerous backfeed into the utility grid, it should be selected and installed by a licensed electrical contractor.
Generac's support material explains the stakes: a transfer switch keeps the home on utility power or generator power, never both at the same time, which prevents back-feeding that could injure utility line workers. Some service-entrance rated switches, such as Generac's 100-amp load center ATS, can act as the utility service disconnect and combine the main breaker, transfer switch and load center in one unit. If your panel is older, full or due for replacement, an electrical panel upgrade can sometimes be planned together with the ATS so the same equipment is not reworked twice.
Gas Supply at Full Load
A 14kW generator needs adequate natural gas or propane at the unit under load. Undersized piping, long runs, an overloaded meter or an incorrect regulator can cause hard starts and shutdowns during an outage. C.S.W. performs plumbing, including gas piping, under Responsible Master Plumber license RMP #46592.
Use the spec numbers as a check. At full load, Generac lists the 14kW model at 243 cubic feet of natural gas per hour, with a required inlet pressure of 3.5–7 inches of water column across all load ranges. A water heater, furnace, range or dryer running at the same time draws from the same meter and piping. On propane, the listed full-load use of 2.92 gallons per hour helps you estimate how long your tank will last and when you would need a delivery.
Placement, Noise and Permits in San Antonio
Generac says installers look for a stable, well-drained spot with enough space to service the generator. Clearances from windows, doors, vents and property lines come from the installation manual and local code, so the exact location should be set during the site visit rather than picked from a photo. Generac lists its home standby generators at an average of 65 to 67 decibels depending on the model, which is worth weighing when the unit will sit near a bedroom window or a neighbor's patio.
Inside San Antonio city limits, the Development Services Department says homeowners must use licensed trade contractors for new electrical, plumbing and HVAC project components, and electrical permits are trade permits issued to contractors licensed by the City or State and registered with the City. Ask whoever installs your 14kW Generac generator to show the permit and inspection plan in the written estimate. If you live in a surrounding community, confirm which authority permits and inspects work at your address.
Keeping a 14kW Generator Ready After Installation
Once the unit is in, the exercise cycle and the maintenance schedule keep it ready. Generac says the exercise can be set to run weekly, biweekly or monthly, and Guardian series units run a 5-minute exercise. For oil, Generac's support guidance calls for the first change after 25 hours of break-in run time and then every 200 run hours or two years. The full standby generator maintenance schedule lists the rest. If a unit started but dropped the load during the last outage, use the after-outage generator repair checklist to record what happened, then schedule generator repair in San Antonio before the next storm.
Comparing 14kW Package Prices
Separate the equipment package from the installed project. A low online price may exclude freight, battery, pad, permit fees, gas piping, electrical materials, trenching, load-management modules, service disconnect changes and startup. Plan permits, placement and inspection with the Generac installation process and permits, and compare broader generator installation cost drivers before you sign.
Frequently asked questions
Is a 14kW Generac generator enough for a whole house?
Sometimes. A 14kW unit can cover many essential loads, and a managed whole-home setup can work when large loads are shed. Central AC, electric heat, electric water heaters and pumps change the answer, so a load review should come before purchase.
Does a 14kW Generac generator need an automatic transfer switch?
A standby generator needs properly rated transfer equipment so generator power cannot backfeed the utility line and the selected loads transfer safely. Whether a service-rated or non-service-rated switch fits depends on your existing service equipment.
Can I buy the generator package online and have C.S.W. install it?
C.S.W. Power Solutions can review a customer-supplied package, confirm whether the model and transfer switch suit the home, and estimate the installation. The equipment still has to match the electrical service, gas capacity, placement requirements and permits.
What costs are not included in a basic generator and ATS package?
Common extras include delivery, battery, pad, permits, gas piping, electrical materials, trenching, load-management modules, panel changes, startup and inspection. Compare installed scope, not just the equipment price, and ask for a written scope that lists each item.
How much gas does a 14kW Generac generator use?
Generac lists its 14kW model 7258 at 189 cubic feet of natural gas per hour at half load and 243 at full load, or 1.76 gallons of propane per hour at half load and 2.92 at full load. Your meter, piping and regulator must deliver that volume at the required pressure while other gas appliances run.
Can a 14kW Generac generator run central air conditioning?
Often, with planning. Generac notes that a 3-ton central AC unit may need up to 15kW to 18kW of starting power, and it suggests pairing a 14kW or 18kW generator with a load manager or soft start kit. Whether your system fits depends on the compressor, your other running loads and how load management is set up.
How loud is a 14kW Generac standby generator?
Generac says its home standby generators average 65 to 67 decibels depending on the model. Placement still matters, so plan the location with bedrooms, patios and neighbors in mind, and follow the clearances in the installation manual and local code.
Sources
- Generac, Home standby generators. Retrieved October 13, 2026.
- City of San Antonio Development Services, Residential permits. Retrieved October 13, 2026.
- Generac, Home Standby Generator, 14kW (model 7258) specifications. Retrieved October 13, 2026.
- Generac, Home Standby Generator, 14kW with Transfer Switch (model 7323). Retrieved October 13, 2026.
- Generac, What Size Generator Do I Need? Sizing Guide. Retrieved October 13, 2026.
- Generac Support, How Do I Correctly Size a Generator for My Home?. Retrieved October 13, 2026.
- Generac, 100A Service Entrance Rated Load Center Automatic Transfer Switch (RXG24SHA1). Retrieved October 13, 2026.
- Generac Support, What is a Manual Transfer Switch?. Retrieved October 13, 2026.
- Generac, Home Standby Generator FAQ. Retrieved October 13, 2026.
- Generac, Backup Generator Installation. Retrieved October 13, 2026.
- Generac Support, What is a generator exercise?. Retrieved October 13, 2026.
- Generac, How do I perform the yearly maintenance for my home standby generator?. Retrieved October 13, 2026.
- Generac, 14kW/18kW specification sheet A0005151081: inlet fuel-pressure ranges. Retrieved October 13, 2026.
Already looking at a 14kW package?
C.S.W. Power Solutions can review the model, transfer switch, panel and gas supply and estimate the installation before you buy. Electrical work is performed under TECL #31793 and gas piping . Call 210-880-2864 or book online.
Related service: Home Generator Installation
Online estimate appointments need at least 24 hours' notice. Need help sooner? Call 24/7: (210) 880-2864.
Or call 210-880-2864